- 您现在的位置：买卖IC网 > Sheet目录17336 > HK10059N1J-T (Taiyo Yuden)INDUCTOR HI FREQ 9.1NH 5% 0402
◆Selection of Flux
1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate the flux, or highly acidic flux is used, an excessive
amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the
surface of the Inductor.
1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may
detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high
humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The
cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux.
◆Soldering
1-1. Preheating when soldering
Heating: Chip inductor components should be preheated to within 100 to 130℃ of the soldering. Cooling: The temperature difference
between the components and cleaning process should not be greater than 100℃.
Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the
soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal
shock.
Recommended conditions for soldering Pb free soldering
［Reflow soldering］
Temperature profile
300
Preheating
60sec. 60sec
230℃
Within 10sec.
300
Peak
260℃ Max.
Within 10sec.
200
Min.
Min.
Slow cooling
200
Slow
cooling
100
100
Preheating150℃ Heating above
60sec. Min.
230℃
0
0
40sec. Max.
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be reflow soldering for 2 times.
Caution
1. The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the thickness of the inductor, as shown
below:
1/2T～1/3T
Inductor
Technical
considerations
Solder
PC board
T
2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to
recommended times as possible.
［Wave soldering］
Temperature profile
300
200
Preheating
120sec. Min.
230～250℃
Within 3sec.
300
200
120sec. Min.
Peak
260℃ Max.
Within 10sec.
Slow cooling
Preheating
Slow
cooling
100
0
100
0
150℃
※Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
※Assured to be wave soldering for 1 time.
※Except for reflow soldering type.
Caution
1. Make sure the inductors are preheated sufficiently.
2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130℃.
3. Cooling after soldering should be as gradual as possible.
4. Wave soldering must not be applied to the inductors designated as for reflow soldering only.
［Hand soldering］
Temperature profile
400
300
230～280℃
Within 3sec.
400
300
Peak
350℃ Max.
Within 3sec.
⊿T
Slow cooling
200
Slow cooling
200
Preheating
100
Preheating
100
150℃ Min.
0
60sec. Min.
0
60sec. Min.
（※⊿Ｔ≦190℃（ 3216Type max）, ⊿Ｔ≦130℃（ 3225 Type min）
※It is recommended to use 20W soldering iron and the tip is 1φ or less.
※The soldering iron should not directly touch the components.
※Assured to be soldering iron for 1 time.
Note: The above profiles are the maximum allowable soldering condition, therefore
these profiles are not always recommended.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E02R01
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EMM08DTKI-S288
CONN EDGECARD 16POS .156 EXTEND
TARW156K020
CAP TANT 15UF 20V 10% AXIAL
HK10054N3S-T
INDUCTOR HIFREQ 4.3+/-0.3NH 0402
GBB15DHND
CONN EDGECARD 30POS .050 DIP SLD
EBM22DRSI-S288
CONN EDGECARD 44POS .156 EXTEND
GEM28DTMN-S189
CONN EDGECARD 56POS R/A .156 SLD
GEM28DTMH-S189
CONN EDGECARD 56POS R/A .156 SLD
REC3-2415SRWZ/H4/A
CONV DC/DC 3W SGL 15V OUT DIP24
相关代理商/技术参数
HK-1005-9N1JTK
功能描述:固定电感器 9.1nH 300mA 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK1005R10J-T
功能描述:固定电感器 INDCTR HIFREQ MLTLYR 0402 100nH 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK-1005-R10JTK
功能描述:固定电感器 100nH 150mA 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK1005R10J-TV
功能描述:100nH Unshielded Multilayer Inductor 150mA 1.5 Ohm Max 0402 (1005 Metric) 制造商:taiyo yuden 系列:HK 包装:剪切带（CT） 零件状态:有效 类型:多层 材料 - 磁芯:铁氧体 电感:100nH 容差:±5% 额定电流:150mA 电流 - 饱和值:- 屏蔽:无屏蔽 DC 电阻（DCR）:1.5 欧姆最大 不同频率时的 Q 值:8 @ 100MHz 频率 - 自谐振:600MHz 等级:AEC-Q200 工作温度:-55°C ~ 125°C 频率 - 测试:100MHz 安装类型:表面贴装 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:0.022"（0.55mm） 标准包装:1
HK1005R10K-T
功能描述:固定电感器 INDCTR HIFREQ MLTLYR 0402 100nH 10% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK1005R10S-T
制造商:TAIYO-YUDEN 制造商全称:Taiyo Yuden (U.S.A.), Inc 功能描述:MULTILAYER CHIP INDUCTOR FOR HIGH FREQUENCY HK SERIES
HK1005R12J-T
功能描述:固定电感器 INDCTR HIFREQ MLTLYR 0402 120nH 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK-1005-R12JTK
功能描述:固定电感器 120nH 300mA 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm